Product Experts Available 1-800-359-7717

Filter Your Results

  1. Remove This Item CATEGORY: Exterior Parts and Trim
 

1969 CAMARO EXTERIOR PARTS AND TRIM

Search Term: 'All Parts'
Category: 'Exterior Parts and Trim'
Vehicle: '1969 CHEVY CAMARO'
Items: 1 to 28 of 1036 Sort by: Show: per page Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  6. Next
Grid  |  List
Best Sellers
Camaro Door Hinge Bushing, Small, Upper Or Lower, 1967-1969 Part # DH-62
Reproduction Of Original Small Diameter Bushing Fits Upper & Lower Door Hinges Sold Separately   Just as regular door hinges are important for securing doors, door hinge bushings are important for protecting and securing your 1967, 1968, or 1969 Camaro’s door hinges. With the passing of time, door hinge bushings inevitably become worn down from excessive use and weather conditions, and may leave your doors getting damaged as your open and close them. To ensure that your doors stay on their hinges and don’t get scratched and scuffed, you should get new hinge bushings for your F-Body Camaro. Rick’s Camaros is happy to offer this small diameter sized door hinge bushing (sold separately), matching factory specifications and replacing your old hinges. With all the hardware you need, the installation of new hinge bushings on your Camaro doors should be easy. Trust Rick’s Camaros for all of your restoration and replacement needs for your 1967, 1968, or 1969 Camaro. Learn More
$2.99 ea.
Camaro Inner Fender Attachment "J" Clip Nut, 5/16", 1967-1969 Part # RC-507
Replacement J Clip Nut Very Close To Original Appearence Black Oxide Finish Used Throughout The Front Sheetmetal This Camaro replacement J clip nut has been manufactured to meet or exceed factory specifications and performance. You will find the fit and function will work perfectly for your Camaro. You will also be pleased to know that Rick's has sourced this J clip nut among other possible parts as the best choice for your repair or restoration project. Learn More
$1.99 ea.
Camaro Floor & Trunk Drain Cover Plate, 1967-1981 Part # PP-13
Correct Stamp Steel Units Seals Holes In Floor And Trunk Pans Requires The Use Of Seam Sealer P/N 88-0187-3 For Proper Intallation 6 Require Per Camaro Your 1967, 1968, 1969, 1970, 1971, 1972, 1973, 1974, 1975, 1976, 1977, 1978, 1979, 1980, or 1981 Camaro floor and trunk drain cover plates serve an important function during final body assembly. At the Fisher Body Plant, your Camaro body goes through a chemical bath which requires full submergence, and having holes scattered throughout the floor and trunk allows these chemicals to drain out when the body is pulled from the tank. Rick's Camaros knows the importance of a correctly restored Camaro and replacing old, leak, rusty or missing drain plates is just as important as any other detail. These reproduction drain plates are not merely replacement plates, but properly stamped units made from correct gauge steel and galvanized for added corrosion protection. Remember to apply the proper body seam sealer during installation, which is offered separately. Trust Rick's Camaros for all of your restoration and replacement needs for your 1967, 1968, 1969, 1970, 1971, 1972, 1973, 1974, 1975, 1976, 1977, 1978, 1979, 1980, or 1981 Camaro!   Learn More

Was: $4.99 ea.

Now: $2.99 ea.
Camaro Door Hinge Bushing, Large, Upper, 1969 Part # DH-63
Door hinge pin large diameter bushings for use with all 69 Camaro upper door hinges. Can also be used when bushing hole is oversize or worn out. Sold individually. Learn More
$1.99 ea.
Camaro Body Plug, 3/4", Rubber, 1967-1969 Part # RC-529
Stock Replacement Fits Various 3/4” Body Panel Access Holes This stock replacement ¾” rubber body plug is manufactured by GM or by one of its authorized suppliers for use as a factory replacement part. You will find the fit and function meets all GM specifications. Using stock replacement parts from Rick's, such as this ¾” rubber body plug, is a sound investment in the restoration or repair of your Camaro.     Learn More
$2.99 ea.
Camaro Bumper Mounting Nut, With Captured Washer, 1967-1969 Part # BU-25
Reproduction Bumper Mounting Nut With Captured Washer Dark Finish As Original Sold Individually The bumper on your 1967, 1968, or 1969 Camaro is one of the defining components that everyone sees while you're on the road. Of course, the bumper isn't able to stay up on its own. Rick's Camaros is happy to offer this reproduction bumper mounting nut for the front or rear bumper of your F-Body. This nut has the correct color, attached washer and size to get you the points you need in the national shows. It will work to secure your front or rear bumper. Don't use a regular nut and lock washer. Trust Rick's Camaros for all of your restoration and replacement needs for your 1967, 1968, or 1969 1st gen Camaro! Learn More
$1.99 ea.
Camaro Door Hinge Pin, Upper Or Lower, 1967-1969 Part # DH-61
Replacement Hinge Pin Upper & Lower Door Hinge Pin Black Phosphate 4 Required Per Car For 1967-1969 Camaro Models The door hinge pins in your 1967, 1968, or 1969 first generation Camaro may be small, but they serve a significant purpose. The door hinge pins are the small steel pieces that hold your F-Body's door hinges together, allowing you to properly open and close your doors. It is possible that these hinge pins could break over time, or go missing. Obviously without these pins, your door assembly will suffer the consequences. Rick's Camaros offers this black phosphate door hinge pin for your upper or lower door hinge. They are sold individually in the case that you only need to correct one of your door hinges, however four would be required to complete your car. Be sure to maintain your Camaro's doors, and keep them functioning properly with new door hinge pins. From racers, show cars, hot rods, and daily drivers, you can trust Rick's Camaros for all of your restoration and replacement needs for your 1967, 1968, or 1969 1st gen Camaro! Learn More
$4.99 ea.
Camaro License Plate Mounting Nut, Square Insert, Rear, 1967-1969 Part # LP-4
Reproduction of Original Plastic Square Push Nut Sold Each Correct License Plate Screws Available as Part # LP-5 This square plastic nut pushes into the body of your Camaro so you can attach your license plate or license plate bracket to the body. This license plate nut makes installing your license plate on your Camaro a snap.   NOTE: These plastic push nuts may also be used for 1969 Grille installation.   Learn More
$0.99 ea.
Camaro Body Plug, 3/4", Plastic, 1967-1969 Part # RC-527
Replacement 3/4" Plasic Body Plug Used In Various Places On The Car This Camaro replacement 3/4" plastic body plug has been manufactured to meet or exceed factory specifications and performance. You will find the fit and function will work perfectly for your Camaro. You will also be pleased to know that Rick's has sourced this 3/4" plastic body plug among other possible parts as the best choice for your repair or restoration project. Learn More
$0.99 ea.
Camaro Hood Adjustment Bolt Bumpers, 1967-1969 Part # WS-60P
Quality Reproduction Hood Bumpers For Above Hood Comes As A Pair Two Required Per Car Replaces GM #3792828 Rick's Camaros is happy to offer this set of hood adjustment bumpers for your 1967, 1968, or 1969 Camaro's hood. This pair of bumpers attaches to the core support and barely touches the bottom of your Camaro hood to keep it in place and protected. As your Camaro rolls down the road, the hood is constanly moving side to side and front to back on the hood hinges. When topped with the rubber hood bumpers, this kit keeps the hood from moving around too much and scraching your Camaro's paint and it keeps the hood from going down too far when it is shut. This set of round rubber bumpers are made to protect the upper part of your hood. Trust Rick's Camaros for all of your restoration and replacement needs for your 1967, 1968, or 1969 1st gen Camaro! Learn More

Was: $6.99 pr.

Now: $2.99 pr.
Camaro Front Sheet Metal Mounting Bolt & Captured Washer, 5/16", 1969 Part # RC-506
Reproduction of Original Black Oxide Plated Hex Head, Pinch Point Bolt with Captured Washer Sold Each Used in Various Locations on the Front Sheet Metal Nice reproduction of a bolt which is usually rusted badly or lost when you are tearing down your Camaro for restoration.This bolt is used on the Camaro in places such as the front inner fenders, radiator core support and many others. Rick's First Generation offers this quality reproduction to let you save time and money on your restoration. Learn More
$1.99 ea.
Camaro Vinyl Top Molding & Glass Molding Clip Pin Studs, 1967-1969 Part # WM-40
Replacement Pin Studs Replace The Rusted Broken Original Studs Used For Attaching Vinyl Clips & Glass Molding Clips To Body Set Of 10 Not everyone has access to a stud welder nor do you have the room for one in your garage. Ricks Camaros knows that adding molding studs due to rust repair or simply upgrading molding level can be a pain without the proper welder. We have the answer! These self-tapping, Phillips head studs feature the same critical head diameter which is the standard in the auto industry for proper clip installation. Additionally, since no welding is required, these studs have higher-quality plating than the standard galvanized, weld-on style. Studs easily tap into any gauge body sheet metal and stop at the proper depth. Make your molding repairs a breeze with these high quality replacement studs from Ricks Camaros.   Learn More
$2.99 Set
Camaro Headlight Retaining Ring, 1967-1975 Part # HH-15
Reproduction Of Original Round Inner Ring Which Holds The Headlight Bulb To The Headlight Bucket 1" Width 2 Required Per Car Comes With Screws With Oval Hole Replaces GM #5950248 Headlight bezels on your 1967, 1968, 1969, 1970, 1971, 1972, 1973, 1974, or 1975 Camaro take several hits over the years, leaving them bruised and battered. Harsh weather conditions damage your headlight bezels while road dirt and rocks beat and sandblast the finish away. Over time, your Chevrolet Camaro bezels start looking tired, and nothing looks worse on a fresh restoration than tired and worn headlight bezels. Rick's Camaros has the solution for you! Our Chevy Camaro headlight sealed beam retaining ring is an accurate reproduction, has correct ring width, and is in original high polished stainless material. The round inner ring holds the headlight bulb to the headlight bucket. From race, restoration or daily drivers, Rick's Camaros is always sourcing from the world’s top manufacturers to bring you the very best 1967, 1968, 1969, 1970, 1971, 1972, 1973, 1974, and 1975 Camaro headlight bezels possible. Learn More
$12.99 ea.
Camaro Fender Emblem, Camaro, 1968-1969 Part # EM-32R
Best Quality Reproduction Camaro Fender Emblem Modeled After 68-69 Camaro Officially Licensed GM Restoration Part  Bright Chrome Over Die-Cast Correct Spacing & Size "C" Is The Correct Height Unlike Other Reproductions Good looking emblems can really make a new paint job on your 1968 or 1969 Camaro shine! Rick's Camaros offers this superior reproduction Camaro fender emblem to make that happen for you. The original GM "Camaro" script fender emblem has become rough around the edges from years of casting and the "C" has become a smudged blob. Let Rick's supply you with a much better emblem which is less than half the price of an original GM emblem (before being discontinued). Matching the original, this die cast emblem has a beautiful chrome finish, adding to the overall shine of your F-Body. Save money and get a better part exclusively at Rick's Camaros. This emblem fits all 1968 and 1969 Standard Camaros, Super Sport (SS) & Z28. Trust Rick's Camaros for all of your restoration and replacement needs for your 1968 or 1969 Camaro! Learn More
$15.99 ea.
$0.99 ea.
Camaro Quarter Window Roller Assembly, Lower, Middle, 1967-1969 Part # QW-6
Officially Licensed Reproduction Contains: Lower Middle Roller With Stud, Slotted Washer, Glass Bushing, Glass Gasket, Special Retaining Nut All Pieces Made Of Original Materials & Correct Plating Fits Driver's (Left) Or Passenger's (Right) Side Two Required Per Car Special Nut Tool Available Separately As Part # HW-26 The lower middle roller on the quarter window of the Camaro takes most of the torque and stress from the window regulator on your 1967, 1968, or 1969 first generation Camaro. Over time, the grease wears out of the quarter window track and even forces work on the roller until the quarter window will eventually not roll up properly. Fix your Camaro quarter windows today with this superior reproduction from Rick's Camaros. Including the lower middle roller with stud, slotted washer, glass bushing and gasket, and special retaining nut, this complete quarter window assembly will fit either the left or right side of your F-Body. All installation tools have correct plating and materials that will exactly match your original assembly. With two required per Chevy Camaro, don't wait to fix the roller assembly for both of your Camaro's quarter windows. From racers, show cars, hot rods, and daily drivers, you can trust Rick's Camaros for all of your restoration and replacement needs for your 1967, 1968, or 1969 1st gen Camaro! Learn More

Was: $12.99 ea.

Now: $10.99 ea.
Camaro Outside Door Mirror, Left, 1968-1969 Part # MR-15
Reproduction of Original Chrome Fits Driver's Side   Includes Mirror Mounting Kit Imported USA Made Mirror Available as Part # MR-6 Nice reproduction of original driver's side door mirror. Rick's First Generation offers this quality mirror for the budget-minded Camaro restorer as an alternative to the expensive original GM mirror.   NOTE: A light coat of your favorite wax on the chrome will enhance the beauty of this mirror and protect it for years to come. Learn More
$34.99 ea.
Camaro Windshield Wiper Blade Assembly, Stainless Steel, 1967-1969 Part # WB-39
Restoration Correct Finish Is Highly Polished Sold As A Pair NOTE: Rubber Refill Does Not Come With Metal Blade 1967-1969 Camaro is a true American icon. The original wiper arms on your 1967-1969 first generation Camaro have endured a lot and most likely look worn and may even be broken. This could pose a problem when you are on the road in bad weather. Do not let it get to this point, and get these great looking, highly polished stainless steel wiper blades for your Camaro today, from Rick's Camaros. Sold as a pair for your windshield, these wiper arms are made from high quality materials and are the correct length for your first generation.  Spruce up your Chevrolet's front end and keep safety a priority. From racers, show cars, hot rods, and daily drivers, you can trust Rick's Camaros for all your restoration and replacement needs for your 1967, 1968, or 1969 first  generation Camaro ! Trust Ricks Camaros for all your part needs. Learn More
$25.99 pr.
Camaro Outside Door Mirror, Right, 1968-1969 Part # MR-14
Reproduction of Original Chrome Fits Passenger's Side   Includes Mirror Mounting Kit Imported USA Made Mirror Available as Part # MR-5 Originally, the passenger's side door mirror was available as a dealer installed option only. Now, you can add the passenger's side door mirror to your car anytime at a great price! Rick's First Generation offers this quality mirror for the budget-minded Camaro restorer.   NOTE: A light coat of your favorite wax on the chrome will enhance the beauty of this mirror and protect it for years to come. Learn More
$34.99 ea.
Camaro Spoiler Mounting Hardware Set, Front, 1967-1969 Part # SB-10
Functional Hardware set contains spoiler to lower valence panel and bracket mounting hardware. Everything necessary to mount a 67-68 or 69 front spoiler. Learn More
$7.99 Kit
Camaro Rocker Panel Molding, Show Correct, 1967-1969 Part # LB-1
Officially Licensed Reproduction Show Quality Exact Duplicate Of Original GM Smooth & Contoured End Points Highly Polished Mounting Bracket & Hardware Included Fits Left Or Right Side Doesn't Fit 1968 Rally Sport These lower rocker panel moldings are simply the best reproductions available for your 1967, 1968, or 1969 First Generation Camaro. Other lower quality and less expensive reproductions out there are not made of the same material and the end points end up blunt, cut jagged or incorrectly bent. Rick's Camaros is proud to offer the best reproduction for your Camaro which includes the large mount bracket and hardware to make installation simple. These show quality moldings are highly polished, have smooth and contoured end points, and include the mounting bracket and extra hardware. When your rocker panel moldings became worn and cracked or fall off, it is time to replace them with these superior moldings. Trust Rick's Camaros for all of your restoration and replacement needs for your 1967, 1968, or 1969 Camaro! NOTE: This molding is used on all 1967-1969 Camaros except the 1968 Rallysport. Learn More
$49.99 ea.
Camaro Windshield Molding Clip Set, Coupe, 1967-1969 Part # WM-26
Reproduction of Original Correct Height, Length and Profile 13 Clips Per Set End Clips Sold Separately as Part # WM-8 Replacement Pin Studs Available Separately as Part # WM-40 Fits 1967-1969 1st Gen Coupes The molding clips for your 1967, 1968, or 1969 first generation Camaro's windshield can often become cracked, brittle, or go missing over the years. The clips and pin studs at the windshield area are also prone to rust due to constant exposure to the elements. This all leaves your windshield moldings unprotected and unable to do their job fully. Rick's Camaros offers this set of reproduction clips which will attach the upper and side windshield moldings to the pin studs on the upper and side of the windshield frame on your Camaro F-Body Coupe. This set comes with 13 clips, all the correct height and length for your Coupe. From racers, show cars, hot rods, and daily drivers, you can trust Rick's Camaros for all of your restoration and replacement needs for your 1967, 1968, or 1969 1st gen Camaro Coupe!  Learn More
$9.99 Set
Camaro Header Panel & Deck Lid Emblem, Camaro By Chevrolet,1968-1969 Part # EM-20R
Officially Licensed GM Restoration Part  "Camaro By Chevrolet" Header Panel & Deck Lid Emblem Bright Chrome Over Die-Cast Correct Inlay Color Correct Spacing & Size Good looking emblems really make a new paint job pop! Rick's Camaros offers this superior reproduction 1968 or 1969 "Camaro by Chevrolet" header panel and deck lid emblem to make that happen for you. The original GM Chevrolet panel and deck emblem on your Camaro has most likely become rough around the edges from years of casting. A rough emblem will only harm your F-Body's image. Let Rick's supply you with a much better panel and deck emblem which is less than ½ the price of an original GM emblem (before it was discontinued). With bright chrome over die-cast, correct inlay color, and correct spacing and size, you can count on this great looking emblem for your Camaro's header panel and deck lid. Trust Rick's Camaros for all of your restoration and replacement needs for your 1968 or 1969 1st gen Camaro! Learn More
$14.99 ea.
Camaro Windshield Wiper Motor Mounting Grommets, With Inserts, Ground Strap & Screws, 1967-1992 Part # WB-17
Correct Reproduction 3 Grommets With Metal Insets, 1 With Ground Strap 3 Mounting Screws Mounts Wiper Motor To Firewall One Set Needed Per Car   Over the years, the rubber grommets on the wiper motor mounts can deteriorate making the wiper motor back away from the firewall. Rick's brings you this correct reproduction kit which allows you to replace your mounts, screws and ground strap all at one time. The attached ground strap allows you to replace this very important piece properly. Proper grounds are extremely important for correct wiper motor function. Replace your wiper motor grommets and screws while you are replacing your wiper motor. Learn More
$14.99 Kit
Camaro Windshield Wiper Arm, Stainless Steel, Coupe, 1967-1969 Part # WB-37
Reproduction Of Original Highly Polished Stainless Steel On Arm & Frame Approx 15" Sold As A Pair Wiper Blades Not Included Fits 1967-1969 1st Gen Camaros The original wiper arms on your 1967, 1968, or 1969 first generation Camaro Coupe have endured a lot and most likely look worn, damaged, and may even be broken. This could pose a problem when you're on the road in bad weather. Don't let it get to this point, and get these great looking, highly polished stainless steel wiper arms for your F-Body today, from Rick's Camaros. Sold as a pair for your windshield, these wiper arms are made from high quality materials and are the correct length for your 1st gen Coupe. Wiper blades are not included with these arms. Spruce up your Chevrolet's front end and keep safety a priority. From racers, show cars, hot rods, and daily drivers, you can trust Rick's Camaros for all of your restoration and replacement needs for your 1967, 1968, or 1969 1st gen Camaro Coupe! Learn More
$34.99 pr.
Camaro Rear Window Glass Molding Clip Set, Coupe, 1967-1969 Part # WM-28
Reproduction of Original Correct Height, Length and Profile 20 Clips Per Set Replacement Pin Studs Available Separately as Part # WM-40 Fits 1967-1969 1st Gen Camaro Coupes The rear window glass on your 1967, 1968, or 1969 first generation Camaro is held together by the work of clips and pin studs. Without them, your glass would become loose and possibly fall out. Over time, these clips and pin studs also can rust from constant exposure to weather elements. Rick’s Camaros is happy to offer you a reproduction rear window glass molding clip set for your Camaro, matching factory specifications and replacing your original glass clips. These clips will attach your rear window moldings to the pin studs on the rear window frame.  Replace the old clips on your F-Body Camaro before installing new windshield moldings with these clip reproductions. Trust Rick’s Camaros for all of your restoration and replacement needs for your 1967, 1968, or 1969 1st gen Camaro! Learn More

Was: $13.99 Set

Now: $9.99 Set
Camaro, License Lamp Assembly, Reproduction, 1967-1969 Part # LP-38
Best Quality Reproduction License Lamp Assembly 12" Brown Lead Wire With Grommet Black Connector & White Lens Gasket Gold Cad Plated Housing Crystal Clear Lens With Correct Lettering Script Includes Plated Screws For 1st Gen Models Camaro clear plastic parts do one of two things over time, they can turn milky and hazy or completely fall apart. Camaro gold cad plating will turn chalky over time. Both of these are main components of your Camaro license lamp assembly. Rick's Camaros offers this superior reproduction 1967, 1968 or  1969 first generation Camaro license lamp assembly to replace that ugly, rusted one on your Camaro. This reproduction assembly includes cad plated housing, socket with bulb, brown color lead wire with grommet and correct black terminal end, crystal clear lens with script, white colored lens gasket, and plated screws. This license lamp assembly is just another one of the best quality parts Rick's Camaros brings you to keep your Camaro Super Sport (SS), Rally Sport (RS), Z28 or Standard correct and looking great always at the best possible price. From racers, show cars, hot rods, and daily drivers, you can trust Rick's Camaros for your restoration and replacement needs for your 1967, 1968, or 1969 1st gen Camaro! Learn More
$22.99 ea.
Items: 1 to 28 of 1036 Sort by: Show: per page Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  6. Next
Grid  |  List
3