Product Experts Available 1-800-359-7717

1975 CAMARO RS CHEVY BODY PARTS

Search Term: 'All Parts'
Category: 'Body Parts'
Vehicle: '1975 CHEVY CAMARO RS'

Items: 1 to 28 of 58 Sort by: Show: per page Page:
  1. 1
  2. 2
  3. 3
  4. Next
Grid  |  List
Best Sellers
Camaro Floor & Trunk Drain Cover Plate, 1967-1981 Part # PP-13
Correct Stamp Steel Units Seals Holes In Floor And Trunk Pans Requires The Use Of Seam Sealer P/N 88-0187-3 For Proper Intallation 6 Require Per Camaro Your 1967, 1968, 1969, 1970, 1971, 1972, 1973, 1974, 1975, 1976, 1977, 1978, 1979, 1980, or 1981 Camaro floor and trunk drain cover plates serve an important function during final body assembly. At the Fisher Body Plant, your Camaro body goes through a chemical bath which requires full submergence, and having holes scattered throughout the floor and trunk allows these chemicals to drain out when the body is pulled from the tank. Rick's Camaros knows the importance of a correctly restored Camaro and replacing old, leak, rusty or missing drain plates is just as important as any other detail. These reproduction drain plates are not merely replacement plates, but properly stamped units made from correct gauge steel and galvanized for added corrosion protection. Remember to apply the proper body seam sealer during installation, which is offered separately. Trust Rick's Camaros for all of your restoration and replacement needs for your 1967, 1968, 1969, 1970, 1971, 1972, 1973, 1974, 1975, 1976, 1977, 1978, 1979, 1980, or 1981 Camaro!   Learn More

Was: $4.99 ea.

Now: $2.99 ea.
Camaro Front End Sheet Metal Bolt Kit, Standard & Rally Sport, 1970-1981 Part # 718880
Reproduction Of Original Correctly Plated Where Applicable 136 Piece Kit Nice reproduction of the bolts and fasteners used to hold the front sheet metal on your camaro. Kit Includes: Headlight Bracket Bolts Hood Latch Brace Bolts Fender Brace Bolts Fender To Core Support Bolts Header Panel End Bolts, Nuts and Washers Upper And Lower Fender Bolts Cup Washers And Bolts For Upper Inner Fenderwells Hood Hinge Bolts Fender Shims Inner Fenderwell J-nuts And Bolts Headlight Bezel Screws Learn More

Was: $41.99 Kit

Now: $38.99 Kit
Camaro Fender To Radiator Support Braces, Chrome, 1970-1981 Part # 33-10352
Chrome Plated To Dress Up Engine Compartment Mounting Bolts Included Rick's Camaro now offers these chrome plated reproduction radiator support bars that won't break the bank! Manufactured from durable steel with a chrome finish, these radiator support braces are sure to be the ticket. The set includes all required mounting hardware. When looking to replace the fender to radiator support braces in your 1970, 1971, 1972, 1973, 1974, 1975, 1976, 1977, 1978, 1979, 1980, or 1981 Camaro, invest in replacements from RIck's Camaro today!  Learn More
$12.99 pr.
Camaro Fender, Right, Front, Inner, 1970-1981 Part # 731244
Reproduction Of Original Right Inner Fender EDP Coated To Ensure Rust Free Delivery Rusty inner fenders on your 1970-1981 SS, RS, Z28. or Type LT Camaro just wouldn’t cut it at the next show. Your Camaro was always meant to outshine other vehicles on the road. However, how can it do that when it begins to rust? Your 1970-1981 Z28 Coupe Camaro won’t get the respect it deserves with its growing blemishes. The inner fenders of your classic Camaro are your friend, as they are crucial in protection for your front wheels, and as such, the fenders are the most heavily prone to damage in the case of minor collisions and more often, rusting over time. Rust can creep up on vehicles and do a lot of damage. The side where the battery is located can drip down battery acid and corrode sizable holes in the inner fender, leaving it lacking in appearance and function. It can be quite costly to fix fender dents and dings on old rusty inner fenders, so it is imperative to do it the right way, the Eckler’s way. Rick’s Camaros brings you this quality reproduction Camaro inner fender made from sturdy sheet metal, so you can start with a clean slate before you paint. Our Camaro fenders are EDP (Electro Deposit Primer) coated, an excellent primer applied electrically, prior to your paint job, which ensures rust-resistant sheet metal and stamped from proper sheet metal gauge. There is no need to waste your time and energy checking rusty areas to weld patch panels at the end of the day, and Rick’s Camaros wants to provide you with quality replacement 1970-1981 Super Sport inner fenders that bolt up like original factory specifications, at a great price. All you have to do is put it on! Treat your 1970-1981 Camaro the way it was meant to be treated: rust free, and replace your inner fenders today at Rick’s Camaros. Applicable On: 1970, 1971, 1972, 1973, 1974, 1975, 1976, 1977, 1978, 1979, 1980, and 1981 Did you know? Many people in our hobby refer to an inner fender as a fender liner. Learn More

Was: $109.99 ea.

Now: $89.99 ea.
Camaro Fender, Left, Front, Inner, 1970-1981 Part # 731243
Quality Reproduction Of Original Left Inner Fender Stamped Steel Construction EDP Coated To Enhance Rust-Resistance Making Your Restoration Easier Rusty inner fenders on your 1970-1981 SS, RS, Z28. or Type LT Camaro just wouldn’t cut it at the next show. Your Camaro was always meant to outshine other vehicles on the road. However, how can it do that when it begins to rust? Your 1970-1981 Z28 Coupe Camaro won’t get the respect it deserves with its growing blemishes. The inner fenders of your classic Camaro are your friend, as they are crucial in protection for your front wheels, and as such, the fenders are the most heavily prone to damage in the case of minor collisions and more often, rusting over time. Rust can creep up on vehicles and do a lot of damage. The side where the battery is located can drip down battery acid and corrode sizable holes in the inner fender, leaving it lacking in appearance and function. It can be quite costly to fix fender dents and dings on old rusty inner fenders, so it is imperative to do it the right way, the Eckler’s way. Rick’s Camaros brings you this quality reproduction Camaro inner fender made from sturdy sheet metal, so you can start with a clean slate before you paint. Our Camaro fenders are EDP (Electro Deposit Primer) coated, an excellent primer applied electrically, prior to your paint job, which ensures rust-resistant sheet metal and stamped from proper sheet metal gauge. There is no need to waste your time and energy checking rusty areas to weld patch panels at the end of the day, and Rick’s Camaros wants to provide you with quality replacement 1970-1981 Super Sport inner fenders that bolt up like original factory specifications, at a great price. All you have to do is put it on! Treat your 1970-1981 Camaro the way it was meant to be treated: rust free, and replace your inner fenders today at Rick’s Camaros. Applicable On: 1970, 1971, 1972, 1973, 1974, 1975, 1976, 1977, 1978, 1979, 1980, and 1981 Did you know? Many people in our hobby refer to an inner fender as a fender liner. Learn More

Was: $109.99 ea.

Now: $89.99 ea.
Camaro Fender To Radiator Support Braces, Black, 1970-1981 Part # 33-10353
Black Mounting Bolts Included Rick's Camaro now offers these painted black reproduction radiator support bars that won't break the bank! Learn More

Was: $12.99 pr.

Now: $9.99 pr.
Camaro Front Fender Repair Panel, Right, 1970-1981 Part # 731132
High Quality Replacement Fender Patch Repair Panel For The Lower Rear End Of Right Front Fender Fits Passenger Side EPD Coated To Ensure Rust Free Delivery   Rusty body panels on your Camaro just won’t cut it at the next show, or on the street for that matter. Your  Camaro was built to outshine the others. But, how can she do that when she starts to rust? Rust can creep up on your classic and do a lot of damage. Your classic beauty won’t get the respect she deserves with her growing blemishes. Rick's Camaros offers a line of repair panels designed to help you cut out the rust and get your baby back in tip top shape. Our heavy gauge stamped steel patch panels offer you the ability to cut the rust out on your Camaro without replacing the entire panel. Our stamped panels are closely shaped to your car’s original body lines, so installation is easier than with an unformed sheet metal panel. Our EPD coated panels give you a leg up on rust prevention. Whether rust has invaded your 1970, 1971, 1972, 1973, 1974, 1975, 1976, 1977, 1978, 1979, 1980 or 1981 Camaro's fender, door or quarter panel, you’re sure to find the patch panel you’re looking for at Rick's Camaros. From show stoppers, racers, hot rods to daily drivers, you can count on Ricks Camaros  for all of your restoration and replacement needs for your 1970, 1971, 1972, 1973, 1974, 1975, 1976, 1977, 1978, 1979, 1980 or 1981 Camaro. Learn More
$33.99 ea.
Camaro Rear Glass To Trunk Filler Panel, 1970-1981 Part # 731032
Quality Reproduction Bolt-In Panel Installs Between Back Glass & Trunk Lid Black EDP Coated Second generation Camaros are notorious for rusting at the rear window and at the trunk hinges. For some unknown reason GM designed this area to hold water like a cereal bowl. As a consequence, this area will rust out and take the mounting tabs of the rear window to trunk panel with it. Replace yours today with this quality reproduction from Rick's and rest assured you are getting the best parts for your restoration. Learn More
$49.99 ea.
Camaro Hood, Cowl Induction, Steel, 1970-1981 Part # 731255
All Steel Construction High Performance Appearance 2-3/4" Rise Eckler's Select Series Fits 1970-1981 2nd Gen Camaros The cowl induction hood on your 1970-1981 second generation Camaro can become worn down over time, whether from rust, paint peeling, dents, or collision damage. No matter what the damage, it is easily visible any time you're on the road. Also, if you feel the need to replace your standard hood with a new edgy style, then it is time to get a new cowl induction hood for your Chevrolet. Rick's Camaros offers this reproduction high performance cowl induction hood for your F-Body's front end. Made from an all steel construction, this cowl hood will give your Super Sport, Rally Sport, Standard, Z28, or Type LT Camaro a great professional look, while also promising to be the most durable option. This cowl induction hood is part of our Eckler's Select Series, and has a 2-3/4 inch height rise. Its crisp, hard lines will look great on your F-Body's front end, revolutionizing your whole look. From racers, show cars, hot rods, and daily drivers, you can trust Rick's Camaros for all of your restoration and replacement needs for your 1970, 1971, 1972, 1973, 1974, 1975, 1976, 1977, 1978, 1979, 1980, or 1981 2nd gen Camaro! Learn More
$329.99 ea.
Camaro Front Fender Repair Panel, Left, 1970-1981 Part # 731301
High Quality Replacement Fender Patch Repair Panel For The Lower Rear End Of Left Front Fender Driver's Side EDP Coated To Ensure Rust Free Delivery   Rusty body panels on your Camaro just won’t cut it at the next show, or on the street for that matter. Your  Camaro was built  to outshine the others. But, how can she do that when she starts to rust? Rust can creep up on your classic and do a lot of damage. Your classic beauty won’t get the respect she deserves with her growing blemishes. Rick's Camaros offers a line of repair panels designed to help you cut out the rust and get your baby back in tip top shape. Our heavy gauge stamped steel patch panels offer you the ability to cut the rust out on your Camaro without replacing the entire panel. Our stamped panels are closely shaped to your car’s original body lines, so installation is easier than with an unformed sheet metal panel.  Our EPD coated panels give you a leg up on rust prevention. Whether rust has invaded your 1970, 1971, 1972, 1973, 1974, 1975, 1976, 1977, 1978, 1979, 1980 or 1981 Camaro's fender, door or quarter panel, you’re sure to find the patch panel you’re looking for at Rick's Camaros. From show stoppers, racers, hot rods to daily drivers, you can count on Ricks Camaros  for all of your restoration and replacement needs for your 1970, 1971, 1972, 1973, 1974, 1975, 1976, 1977, 1978, 1979, 1980 or 1981 Camaro. Learn More
$33.99 ea.
Camaro Rear Floor Pan, Left, 1970-1981 Part # 731018
Reproduction Of Original Rear Floor Pan Repair Panel 22" Length X 26" Width Natural Steel Finish Left (Driver's Side) Rick’s Camaros stamped steel sheet metal floor pan repair panels are crucial when rust rears its ugly head. 1970-1981 Camaro floor pans take a beating over the years and are rarely rust-free. Rick’s Camaros sources sheet metal floor pans from the world’s premium manufacturers to bring you only the very best for your restoration. F-Body floor pans are stamped on heavy ton equipment from correct gauge steel to ensure factory style contours and maximum rigidity over originals. The left side floor pan covers the rear section from the back of the front seat to the rear seat of your Second Generation Camaro. Floor pans from Rick’s Camaros must be welded in and usually fitted, so never cut out your original floor pans before receiving replacements. We highly recommend the use of a skilled body shop when installing replacement Camaro floor pans and to always check other related items such as floor braces, rocker panels, toe panels and seat supports for other potential replacement needs. We have sold thousands of sheet metal floor pans and will stand by each purchase to make sure that your 2nd generation Camaro is restored to perfection. From racers, hot rods or daily drivers, trust Rick’s Camaros for all of your restoration and replacement needs for your 1970, 1971, 1972, 1973, 1974, 1975, 1976, 1977, 1978, 1979, 1980, or 1981 Camaro!   Learn More
$44.99 ea.
Camaro Rear Floor Pan, Right, 1970-1981 Part # 731019
Reproduction Of Original Rear Floor Pan Repair Panel 22" Length X 26" Width Natural Steel Finish Right (Passenger's Side) Rick’s Camaros stamped steel sheet metal floor pan repair panels are crucial when rust rears its ugly head. 1970-1981 Camaro floor pans take a beating over the years and are rarely rust-free. Rick’s Camaros sources sheet metal floor pans from the world’s premium manufacturers to bring you only the very best for your restoration. F-Body floor pans are stamped on heavy ton equipment from correct gauge steel to ensure factory style contours and maximum rigidity over originals. The right side floor pan covers the rear section from the back of the front seat to the rear seat of your Second Generation Camaro. Floor pans from Rick’s Camaros must be welded in and usually fitted, so never cut out your original floor pans before receiving replacements. We highly recommend the use of a skilled body shop when installing replacement Camaro floor pans and to always check other related items such as floor braces, rocker panels, toe panels and seat supports for other potential replacement needs. We have sold thousands of sheet metal floor pans and will stand by each purchase to make sure that your 2nd generation Camaro is restored to perfection. From racers, hot rods or daily drivers, trust Rick’s Camaros for all of your restoration and replacement needs for your 1970, 1971, 1972, 1973, 1974, 1975, 1976, 1977, 1978, 1979, 1980, or 1981 Camaro! Did you know? Many people in our hobby refer to floor pans as floor boards, floorboards, body panels, or sheet metal.   Learn More
$41.99 ea.
Camaro Cowl Vent Grille Screen, 1970-1981 Part # 731363
Reproduction Of Original Mounts to Top Of Upper Cowl Panel Made From Injection Molded Plastic    This Camaro reproduction cowl vent grille screen has been manufactured to original factory specifications using today's modern manufacturing techniques. You will find the fit, finish and function will work superbly for your restoration. In addition, using a reproduction cowl vent grille screen from Eckler's will add authenticity and value to your Camaro.     Learn More
$64.99 ea.
Camaro Trunk Lid, 1970-1981 Part # 731062
Reproduction Of Original Drilling For Rear Spoiler Is Required Eckler's Select Series Learn More

Was: $159.99 ea.

Now: $149.99 ea.
Camaro Shifter Hump, Manual, With Or Without Console, 1970-1981 Part # 731377
Quality Reproduction Correct Gauge Metal Stamped Steel With Or Without Console This shift hump patch panel is a must when converting an automatic car to a 4-speed or doing a 5-speed conversion. Without this panel installed in the floor, there will be nothing to mount the shift boot to in your Camaro. NOTE: This patch panel will need to be worked with a hammer around the edges to insure a snug fit just as the originals did. Learn More
$68.99 ea.
Camaro Braces, Fender To Radiator Support, 1970-1981 Part # 731400
Reproduction of Original Original 1973 Rally Sport Braces Are Longer, But These Will Fit As A Replacement This Camaro reproduction fender to radiator support braces has been manufactured to original factory specifications using today's modern manufacturing techniques. You will find the fit and function will work superbly for your restoration. In addition, using reproduction fender to radiator support braces from Rick's will add authenticity and value to your Camaro. Learn More

Was: $27.99 pr.

Now: $24.99 pr.

Was: $99.99 ea.

Now: $69.99 ea.

Was: $99.99 ea.

Now: $69.99 ea.
Camaro Standard Hood, 1970-1981 Part # 731314
Reproduction Of Original Original Flat Style Hood Learn More
$288.99 ea.
Camaro Rear Inner Wheel Housing Mini Tubs, Deep, Detroit Speed & Engineering (DSE), 1970-1981 Part # 721550
Inner Tubs Only (Connect To Stock Outer Wheel Wells) Allows Almost 3” More Clearance Accommodate Wheels Up to 12” wide While Retaining Stock Appearance Stamped From 18 Gauge Steel Use with offset shackles P/N DS-26, lower shock plates P/N DS-16 & DS-17, & a narrow fuel tank (See Below)  NOTE: Complete mini-tub kits available! Please see below. Learn More
$379.99 pr.
Hood Scoop, L88 Style, Fiberglass, Extra Long And High Part # 88-1920-3
Hand Laminateded Fiberglass High-Performance Upgrade Measures 58" Long, 29 Wide And 5" High A fiberglass hood scoop will perfectly complement the high-performance look of your classic Camaro. A fiberglass hood scoop works hard to allow air flow directly into the engine compartment. Depending on your need, this part is cross-functional as a performance and decorative piece. Constructed of fiberglass, this part is built for achieving peak-performance. Fiberglass offers a lightweight alternative to heavy stamped steel materials. It is also advantageous because of better gas mileage and the pronounced stylish look that will result.  Whether you’re entering a NHRA event that requires your classic to have a hood scoop or you’re just completing your long-time restoration, Ecklers has you covered. Invest in a L88-Style fiberglass hood scoop for your classic Camaro. Available at Rick's Camaro today!  This hand laminated L88 hood scoop will bond to any hood. The extra-long (58") scoop will give extra room for those large engines with all the accessories. These fiberglass body panels are made of the finest automotive grade resins, 1-1/2 oz. mat (3 layers) and 21 mils of soft-sanding gelcoat. Eckler's panels are wave-free because of the heavily reinforced molds that are copied from original GM panels and they are allowed to cure 24 hours before being pulled from the molds.   Learn More
$259.99 ea.
Camaro Trunk Weatherstripping Channels, 1970-1981 Part # 731385
Reproduction Of Original Trunk Weatherstrip Fits In This Channel Needed For New Full Quarters Replace Old Rusty Pieces Set Of 2 Pieces New Proprietary Tooling For 2nd Gen Camaros Replaces GM #8797256 & 20109028 The gutter panel moldings can rust and wear on the quarter channels of your 1970-1981 second gen Camaro. Rick's Camaros offers this set of two gutter weatherstrip moldings, which are accurate reproductions of the original gutter edge moldings to finish out both quarters, allowing the installation of the trunk weatherstrip on your F-Body. This gutter set features new proprietary tooling, and the uniform edge on these gutter panels gives the trunk a correct factory look. These are needed on all full reproductions and 80% quarters or for repair of your rusted originals. Don't wait to replace! Trust Rick's Camaros for all of your restoration and replacement needs for your 1970, 1971, 1972, 1973, 1974, 1975, 1976, 1977, 1978, 1979, 1980, or 1981 2nd gen Camaro! Learn More

Was: $74.99 pr.

Now: $69.99 pr.
Camaro Inner Rocker Panel, Left, 1970-1981 Part # 731417
Reproduction Of Original Completes The Rocker Box By Welding Inside P/N 731109 Learn More
$129.99 ea.
Camaro Full Floor Pan, Right, 1970-1981 Part # 731283
Best Quality Reproduction Full Floor Pan Repair Panel 77" Length X 28-1/2" Width Includes Half Of Transmission Tunnel Includes Under Rear Seat Panel Bare Steel Right (Passenger's Side) Made In The USA Rick’s Camaros stamped steel sheet metal floor pan repair panels are crucial when rust rears its ugly head. 1970-1981 Camaro floor pans take a beating over the years and are rarely rust-free. Rick’s Camaros sources sheet metal floor pans from the world’s premium manufacturers to bring you only the very best for your restoration. F-Body floor pans are stamped on heavy ton equipment from correct gauge steel to ensure factory style contours and maximum rigidity over originals. The right side full floor pan reaches from the toe board to under the rear seat and center of transmission hump to rocker panel on your Second Generation Camaro. Floor pans from Rick’s Camaros must be welded in and usually fitted, so never cut out your original floor pans before receiving replacements. We highly recommend the use of a skilled body shop when installing replacement Camaro floor pans and to always check other related items such as floor braces, rocker panels, toe panels and seat supports for other potential replacement needs. We have sold thousands of sheet metal floor pans and will stand by each purchase to make sure that your 2nd generation Camaro is restored to perfection. From racers, hot rods or daily drivers, trust Rick’s Camaros for all of your restoration and replacement needs for your 1970, 1971, 1972, 1973, 1974, 1975, 1976, 1977, 1978, 1979, 1980, or 1981 Camaro! NOTE: This floor pan does not have provisions for a catalytic converter. Learn More
$289.99 ea.
Camaro Roof Panel, 1970-1981 Part # 731330
Reproduction Of Original This Camaro reproduction roof panel has been manufactured to original factory specifications using today's modern manufacturing techniques. You will find the fit, finish and function will work superbly for your restoration. In addition, using a reproduction roof panel from Eckler's will add authenticity and value to your Camaro. Learn More
$336.99 ea.
Camaro Inner Rocker Panel, Right, 1970-1981 Part # 731418
Reproduction Of Original Completes The Rocker Box By Welding Inside P/N 731108 Learn More
$129.99 ea.
Items: 1 to 28 of 58 Sort by: Show: per page Page:
  1. 1
  2. 2
  3. 3
  4. Next
Grid  |  List
4