CAMARO EMISSIONS SYSTEM PARTS FOR 'ALL YEARS AND MODELS'
Rick's Camaros we ensure you'll find high-quality Camaro emissions hoses at the lowest prices around. We have a wide selection of Camaro emission control parts. Rick's Camaros is the most trusted name in Camaros, because we love them as much as our customers do. That's why we're committed to bringing you the best in Camaro emissions parts for your emission control system.
Reproduction of Original Long, Cut to Length Hose Molded 90° End (2) Correct Black Pinch Style Clamps Nice reproduction of the original Camaro Positive Crankcase Ventilation (PCV) hose. On most Camaro applications the PCV hose runs from the PCV valve in the valve cover or oil fill tube (molded end) to a large fitting on the base plate of the carburetor. Replace your original oily, cracked original PCV hose with a new one from Rick's First Generation. Learn More
Reproduction Of Original Black Oxide Finish Fits Most 1/2” PCV Valve & Brake Booster Hoses These little black pinch clamps are used on the engine for various 1/2” hoses. Usually, they are found on the PCV valve, the brake booster and the intake where these meet the intake fittings. Replace your incorrect worm gear clamps with these correct black oxide pinch clamps today from Rick’s and keep your car show fresh! Learn More
Quality Reproduction Reinforced Rubber For Cowl Induction Small Block Cars ONLY Length = 4½" Large End ID = .940" Small End ID = .750" Rick's offers this quality reproduction of the Cowl Induction crankcase vent hose to keep your restoration technically correct. This hose runs from the elbow on the valve cover up to the elbow on the bottom of the Cowl Induction air cleaner and is an integral part of the PCV system on your Camaro. Keep your car show and go ready with this quality reproduction from Rick's First Generation. Learn More
Reproduction Of Original Bright Yellow Paint Fits 5/16" Emission & Fuel Hoses Some Applications Used Up To 12 Clamps For The EEC System A Functioning EEC System Required In Most Emission Controlled States In 1970 under increasing pressure from EPA regulations, GM began to add evaporative emissions controls to many vehicles. The Camaro was no exception. Keep your emissions system functioning properly by replacing your hose clamps with these quality reproductions from Rick's All Generations. NOTE: What is EEC? EEC is an acronym for Evaporative Emission Control. It usually appears as a second and third vent port at the front of the gas tank. These ports act as a return line from the charcoal canister, fuel pump and vapor separator. EEC usually appeared on vehicles produced for sale in California and other emissions controlled states. Learn More
Stock Replacement This stock replacement EGR valve is manufactured by GM or by one of its authorized suppliers for use as a factory replacement part. You will find the fit, finish and function meets all GM specifications. Using stock replacement parts from Eckler's, such as this EGR valve, is a sound investment in the restoration or repair of your Camaro. Learn More
Restoration Correct Original GM Replacement For 75-78, 80, 85-87 Years For V8 Engines Correct Fit Made In USA In many engines this Thermal Ported Vacuum Switch is broken off at the thermostat housing, or because of the age of the switch it has stopped working all together. Replace the switch on your 1975, 1976, 1977, 1978, 1980, 1986 or 1987 Camaro, with this factory original AC Delco part from Ricks Camaros. Just in time for showcar season or that weekend cruise, now you can replace that missing or defective thermal ported vacuum swith for your 1975, 1976, 1977, 1978, 1980, 1986 or 1987 Camaro. You can trust Ac Delco for the correct parts at the best quality, just as you can trust Ricks Camaros for all your parts needs. Learn More
Reproduction Stamped Steel Deep Groove For High Horsepower Engines Nice reproduction of the Smog system pulley for the Camaro. This pulley attaches over the smog pump fan and is driven off of the crankshaft. Learn More
Remanufactured To Meet Or Exceed Factory Specs Features New Rotor Bearings & Fan Filters For Use With V8 Engines Only Restoration Correct Are you hearing a noise or is the A.I.R. pump missing from your 1972-1979 Camaro? Ricks Camaros has this correct replacement pump available. Just in time for showcar season or that cruise to the local soda shop, Ricks Camaros has the correct A.I.R. pump for your 1972, 1973, 1974, 1975, 1976, 1977, 1978, 1979 Camaro. Trust Ricks Camaros for all your parts needs. Learn More
Correct Reproduction Smog Air Injection Check Valve Single Inlet Valve Improves Air Emissions Gold Iridite Plating As Original For Small & Big Block Engines Fits 1967-1969 1st Gen Camaro Models The exhaust manifold air injection tubes are important for reducing the exhaust smog fumes from your 1967, 1968, or 1969 first generation Camaro. Especially when starting up your car, the engine can emit a heavy amount of smog, which can be harmful to your F-Body, as well as the space around your car. Rick's Camaros now offers these reproduction smog tubes, extension tubes, and check valves, part of the injection reactor tubes from the Air Injection Reactor (AIR) engine system, manufactured to replace your original worn tubes and valves. Acting as a smog inhibitor pump to instead emit clean air, the single inlet check valve works to vastly improve your air emissions. Each tube is manufactured with correct bends and outlets for installation onto the exhaust manifold. A correct threaded outlet head is installed for easy installation of the smog pump check valves, and is produced in a gold iridite plating just like the original. Aside from looking great among your engine compartment, these smog tubes are a great environmental decision for your Chevy Camaro. From racers, show cars, hot rods, and daily drivers, you can trust Rick's Camaros for all of your restoration and replacement needs for your 1967, 1968, or 1969 1st gen Camaro! Learn More
Replacement Valve This Camaro replacement PCV valve has been manufactured to meet or exceed factory specifications and performance. You will find the fit and function will work perfectly for your Camaro. You will also be pleased to know that Eckler's has sourced this PCV valve among other possible parts as the best choice for your repair or restoration project. Learn More